Adler problem ammo list thread

Double barrel, side by side, over-under, semi-automatic, straight-pull and lever action shotguns.

Adler problem ammo list thread

Post by MtnMan » 28 May 2022, 6:14 am

After getting a new Adler B220 I thought it might be useful to have a list of Ammo's that people have experienced a problem with. Fail to eject, feed, etc.

List Adler model, ammo and problem experienced and if you found a solution.
MtnMan
Corporal
Corporal
 
Posts: 330
Queensland

Re: Adler problem ammo list thread

Post by Blr243 » 28 May 2022, 3:18 pm

Good idea eley aaa loads in my 220 Adler lockup tight after firing very difficult to cock the handle rear wards
Blr243
Brigadier
Brigadier
 
Posts: 4479
Queensland

Re: Adler problem ammo list thread

Post by MtnMan » 28 May 2022, 3:28 pm

Just bought some of them as they were the only AAA's in the gunshop in the big smoke near me.
MtnMan
Corporal
Corporal
 
Posts: 330
Queensland

Re: Adler problem ammo list thread

Post by MtnMan » 28 May 2022, 6:08 pm

Haven't had any trouble yet with any Eley BB ,AAA or SG. Remington #4 &#6 all good. All high brass.
MtnMan
Corporal
Corporal
 
Posts: 330
Queensland

Re: Adler problem ammo list thread

Post by wazz » 28 May 2022, 7:36 pm

Never had a fail to feed or hard to eject mine digests everything I feed it.
wazz
Recruit
Recruit
 
Posts: 12
New South Wales

Re: Adler problem ammo list thread

Post by jovialjosie2002 » 28 May 2022, 7:38 pm

I've tried winchester, slugs buck and shot....Winchesters AA hulls and cheap (made in france) hulls never a problem.
Remington (b&p made in Italy) AAA & target loads....never a problem
B&P target loads....never a problem.
Falcon cowboy loads....never a problem.
I've never heard of anyone having an issue with anything but Elley.
However, see our recent topic on the trigger assembly falling out. .......it's a cheap shotgun.....enjoy.....don't expect it to last 100,000 rounds....lol
jovialjosie2002
Private
Private
 
Posts: 73
Queensland

Re: Adler problem ammo list thread

Post by goldiexxxx » 29 May 2022, 5:05 am

Adler B220
Remington high brass nearly always gets difficult to extract. Never had any problems with any brand of low brass ammo.
goldiexxxx
Private
Private
 
Posts: 75
Queensland

Re: Adler problem ammo list thread

Post by jovialjosie2002 » 29 May 2022, 8:26 pm

goldiexxxx wrote:Adler B220
Remington high brass nearly always gets difficult to extract. Never had any problems with any brand of low brass ammo.


Is that "Remington" high brass made in Italy by b&p?????
You can check on the box, it will clearly say that it's made by b&p in Bologne.
jovialjosie2002
Private
Private
 
Posts: 73
Queensland

Re: Adler problem ammo list thread

Post by jovialjosie2002 » 27 Jun 2022, 3:08 pm

goldiexxxx wrote:Adler B220
Remington high brass nearly always gets difficult to extract. Never had any problems with any brand of low brass ammo.


I just shot some Remington AAA buckshot (made by B&P in Italy and labelled "Remington"). It was hard to extract, a mallet would have been handy. The plastic hulls look deformed after I extracted them. However, when I shot the same ammo in my ou baikal e27 I had no issues.
jovialjosie2002
Private
Private
 
Posts: 73
Queensland


Back to top
 
Return to Shotguns - 12 gauge, 28 gauge, 410 bore etc.