Sealing a recoil pad

Improving and repairing firearms. Rifle bedding, barrel work, stock replacement and other ways to improve your firearms.

Sealing a recoil pad

Post by inventurkey » 13 Mar 2015, 10:33 am

This is thinking of the stories of a bit of copper solvent or lead remover getting rubbed or spill onto a recoil pad and the recoil pad melting into goo all over the floor of your safe.

Is there something like the sealants your spray on your shoes to water proof them that you could spray on soft recoil pads to protect them from this?
Savage Axis Stainless in .308
Tikka Lite .22-250 Rem
User avatar
inventurkey
Lance Corporal
Lance Corporal
 
Posts: 170
Western Australia

Re: Sealing a recoil pad

Post by Jack V » 14 Mar 2015, 9:37 pm

You can apply Vaseline to the pad an d buff it off to a shine . Clear boot polish might work also . Lacquer is not that good as it cracks eventually and looks bad .
There is a product called Slick Eze . I have no clue where you could get it but it is for treating recoil pads . Not sure how suitable it is though.
Jack V
Sergeant
Sergeant
 
Posts: 693
New South Wales

Re: Sealing a recoil pad

Post by brett1868 » 14 Mar 2015, 11:24 pm

How would something like armour all or similar go? I've never put much thought into protecting recoil pads from cleaning solvents as I never let them get near the pad in the first place.
How's my posting?
Complaints, Concerns - 13 11 14
User avatar
brett1868
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3017
New South Wales

Re: Sealing a recoil pad

Post by Jack V » 15 Mar 2015, 1:13 pm

I have never tried Armor all . I agree the best option is don't let solvents or oil near the pad .
When you clean your gun use an O ring sealed bore guide and lay a cloth over the stock to protect it .
Jack V
Sergeant
Sergeant
 
Posts: 693
New South Wales

Re: Sealing a recoil pad

Post by Warrigul » 15 Mar 2015, 4:30 pm

Track and sail is good for anything delicate, just hold it back a bit when spraying so you don't get too much propellant on the surface. Any silicone based lube is generally a safe bet.

You should store anything muzzle down, especially if it has a recoil pad.
Warrigul
Warrant Officer C2
Warrant Officer C2
 
Posts: 1103
-

Re: Sealing a recoil pad

Post by inspector » 16 Mar 2015, 6:38 pm

Scotch Guard?
User avatar
inspector
Private
Private
 
Posts: 95
Victoria

Re: Sealing a recoil pad

Post by inventurkey » 16 Mar 2015, 6:39 pm

Jack V wrote:There is a product called Slick Eze . I have no clue where you could get it but it is for treating recoil pads . Not sure how suitable it is though.


One to keep an eye out for.
Savage Axis Stainless in .308
Tikka Lite .22-250 Rem
User avatar
inventurkey
Lance Corporal
Lance Corporal
 
Posts: 170
Western Australia

Re: Sealing a recoil pad

Post by inventurkey » 16 Mar 2015, 6:41 pm

brett1868 wrote:I've never put much thought into protecting recoil pads from cleaning solvents as I never let them get near the pad in the first place.


Jack V wrote:I agree the best option is don't let solvents or oil near the pad


Neither do I deliberately of course. Guarding against accidents is all ;)
Savage Axis Stainless in .308
Tikka Lite .22-250 Rem
User avatar
inventurkey
Lance Corporal
Lance Corporal
 
Posts: 170
Western Australia

Re: Sealing a recoil pad

Post by inventurkey » 16 Mar 2015, 6:42 pm

Warrigul wrote:You should store anything muzzle down, especially if it has a recoil pad.


I do already :)

Just using the gooey floor mat to emphasize the question.
Savage Axis Stainless in .308
Tikka Lite .22-250 Rem
User avatar
inventurkey
Lance Corporal
Lance Corporal
 
Posts: 170
Western Australia

Re: Sealing a recoil pad

Post by Yelp » 16 Mar 2015, 6:45 pm

inventurkey wrote:Neither do I deliberately of course. Guarding against accidents is all ;)


Good philosophy.

Storing muzzle down you don't need to worry about run off. I'd just through a cloth over it personally. A pad should last without additional protection, just keeping it dry.
User avatar
Yelp
Lance Corporal
Lance Corporal
 
Posts: 221
Queensland

Re: Sealing a recoil pad

Post by Mich » 21 Mar 2015, 8:07 am

inventurkey wrote:Neither do I deliberately of course. Guarding against accidents is all ;)


Keep a small plastic bag and masking tape handy for cleaning to wrap the pad in, easily removed too.

That'll cover you.
User avatar
Mich
Lance Corporal
Lance Corporal
 
Posts: 182
United States of America


Back to top
 
Return to Gunsmithing