Guess what I'm making

[deye243]

Probably a dead giveaway but this is the first pic

IMG_1730 (Small).JPG (50.86 KiB) Viewed 6807 times

[anthillinside]

Ummmm.. a Saturn IV rocket

[deye243]

another pic

IMG_1729 (Small).JPG (52.49 KiB) Viewed 6782 times

[North East]

I give up.

[FuzzyM]

Pod for burying an L1A1 SLR?

[FuzzyM]

Probably a bit small actually.
Maybe a mother in law suppressor?

[deye243]

i was gunna just put up one pic a a time but this should tell ya

IMG_1734 (Small).JPG (50.13 KiB) Viewed 6773 times

[anthillinside]

Still recon a Saturn IV

Will it blend?

Or will they come out shiny

[cruze82]

no idea

[on_one_wheel]

If it's a penis pump your making, you had better round those edges off !

[North East]

I've never seen a deer made out of PVC....although a first time though.

[Combat_Wombat]

Tactical bong?

[deye243]

If it's a penis pump your making, you had better round those edges off !

hahahaha see all that PVC powder on the floor in the pic

http://austargets.com/forum/index.php

ya should get it now this is just the tub the rest comes after i kick the welder in the guts

[cruze82]

still no idea

[deye243]

well it will have 10lb of stainless steel pins in it

[anthillinside]

So it's the new improved model, Saturn V.
What are you going to spin it with?

[deye243]

will post the pics when i have made the base and hooked up the donk and sprockets

this the donk 1 hp @ 1400 rpm should do it

$_57 (Small) (2).JPG (39.11 KiB) Viewed 6628 times

[anthillinside]

I was right !
With that much power, the brass could well end up on the moon
Can't wait to see the finished project

[deye243]

i ordered a 1/3hp @1400rpm but i don't think it will be enough as the tub full will be 26 to 30lb

[deye243]

this is a couple of pics of a tumbler i built 20 years ago when i was pistol shooting

in the 1st is where the singer sewing machine motor went and the 2nd where the

o ring belt went and the 240V dimmer was the speed controller.

IMG_1737 (Small).JPG (87.12 KiB) Viewed 7153 times

IMG_1738 (Small).JPG (88.46 KiB) Viewed 7153 times

[North East]

[deye243]

i didn't get much done today i have to do more load work on my 6mm but i got the base cut now to find a welder

IMG_1740 (Small).JPG (58.86 KiB) Viewed 6958 times

[roob]

I was going to say potato canon

[deye243]

don't worry when i seen the thickness of the side walls i was thinking s**t this stuff would handle a ****** of pressure

[deye243]

now i just have to wait for the motor pulleys and bearings to roll up

12mm Brite steel shaft

IMG_1741 (Small).JPG (75.32 KiB) Viewed 6948 times

[RoginaJack]

I was gonna say a vibrator but the steel needles? Kinky, eh?

[Wheelbarrow]

Looks like you're about to run your laptop over a bandsaw

[deye243]

now i might get something done this weekend ....... got the agitator in and the bearings turned up as well

IMG_1744 (Small).JPG (45.74 KiB) Viewed 6926 times

IMG_1743 (Small).JPG (36.58 KiB) Viewed 6926 times

[Wes]

Still no idea here

[deye243]

not much progress (life sucks without a shed) but i am still waiting for the motor

and the pulleys so i can do a proper mockup and mod where i have to.

IMG_1772 (Small).JPG (61.46 KiB) Viewed 6895 times

IMG_1774 (Small).JPG (52.99 KiB) Viewed 6895 times

IMG_1773 (Small).JPG (46.58 KiB) Viewed 6895 times

hmm i think i will shorten the base by about 5 or 6 inch's for a start