White River primers

[Wapiti]

Hi fellas,
Was wondering if anyone has switched to these and how the change affected their loads, if at all?

Went into town last week and went to get some Winchester LR, was told their distributor hasn't any left and allocation for regional areas was unknown for the future. I have been using WLR and WLRM primers since the Covid world-changing-experiment as I couldn't get CCI or Federal at all, and haven't had any issues.
Gotten used to the cheap un-plated little primers.

Now without any idea of when if ever I can get more, I had a choice between the Indian-made ones, and these White River chrome-plated jobs from the USA.
Anyone found any differences and have any cautions?

[hawks667]

Have loaded & fired over 300 of them in the 243. No issues at all. All went bang and accuracy fine.

About 150 used in the 308 & also fine..

[JDM9691]

I chose to begin reloading a couple years back when primers were unavailable. When the LGS got some in White River LR were the only ones available, and the 800 i've used have all been fine. Only had 1 go pop, but I suspect I skipped putting powder in that one. Ooops!
Did scrounge some Win LR primers and results didn't seem different, but It was early days and I was trying a couple powders as well.
They all went bang, and that's all I was looking for back then.

[mchughcb]

Got a heap during covid. Haven't run out of cci yet to test. Id only heard anecdote that they are a little tighter and linger than cci but havent loaded to say if its true.

[Fester]

They all seem pretty reliable, and all those weird brands were less consistent with the seating pressure needed.
The White River LR were the tightest of them all, and would have destroyed my RCBS Universal hand primer, plus the risk of being so tight that a slight chance of going off. A bloke on another forum knows about near de-gloving his fingers, and has a hole in the ceiling where bits of the hand primer went through.

I set up a Lee benchtop unit for more leverage and safety; the primer going in is separated so the rest shouldn't go off.

The next worst were the Ruag SR, RWS, but they could be forced to seat without the ring mark like the White Rivers had on every seated primer, no matter what I did to avoid it.
I saved the last few packs for if I end up with a big enough batch of Federal cases with loose pockets that are not showing any splits.
I never bought a second box.

The Indian #34s were inconsistent to seat, but not as tight as the White Rivers, and I did buy a second box.
They were hotter, but assured they were modern, and not corrosive like old military stuff could be.
Other blokes liked them when they couldn't buy RL Magnum primers.

The shops are all discounting those new import brands as even CCI are back now.
I never actually run out; I just bought them for Justin.

I have a warmed-up 2213SC hunting load that benefited from those hotter Indian primers so it will save my CCI stocks a bit.

[Wapiti]

Thanks guys, for all your info.
Hopefully I can get a few of these into some brass tomorrow evening and see how they go.
I'll compare them on a target with a load I know, always use and know the velocity of. That'll be a good experiment as to what a primer change does to a load.

[Damo300]

No problems here.
Using them at the moment in 243 and 30/30.
I actually loaded up some 300wm when the magnum primers were non existent.
Worked very well.

EDIT...
Have been running CCI, and RWS in the past.
Loads didn't change much for this hunters eyes.
Speeds are roughly the same.

I also use them in an empty case in the 30.30 to scare off the corellas when they get unbareable.
Happening a lot lately. Not sure on the drought conditions out west but these birds tend to flock to our area when the food supply runs low. I thought they got rain out there recently.
The retirement village residents next door think I'm throwing fire crackers at them, so they ask me to rid these birds all the time because they eat their arcatraves, fly screens, plants, even the dogs bed must have has some kind of yummies because they destroyed that too.
Just a bigger locust.

[deye243]

I loaded some in a 708 for a mate and noticed they are very soft so I would not load on the warm side if I was you