T3x 10 moa rail

Rifle scopes, iron sights and optics. Spotting scopes and target acquisition devices.

T3x 10 moa rail

Post by scoot » 16 Nov 2026, 12:35 pm

Anyone know where I can find a 10 or 15 moa picatinny rail for a tikka t3x. Everything i can find is 0 or 20 but for what I'm doing a 10 would be more betterer.
I have got some burris zee rings with the offset inserts but I find them a bit tedious to set up initially.
User avatar
scoot
Corporal
Corporal
 
Posts: 262
South Australia

Re: T3x 10 moa rail

Post by bigrich » 16 Nov 2026, 3:56 pm

scoot wrote:Anyone know where I can find a 10 or 15 moa picatinny rail for a tikka t3x. Everything i can find is 0 or 20 but for what I'm doing a 10 would be more betterer.
I have got some burris zee rings with the offset inserts but I find them a bit tedious to set up initially.


maybe find a cluey gun smith or machinist who can machine down a 20 moa rail to what you want . tikka's have a flat topped receiver so it shouldn't be too hard i think . cheers :thumbsup:
bigrich
General
General
 
Posts: 6756
Queensland

Re: T3x 10 moa rail

Post by Wapiti » 16 Nov 2026, 5:43 pm

Yes, do it in a mill.
Grabbing it, setting it up and getting the amount right would take out the calculator mate and get that right. That would cost the price of 4-6 10 MOA factory rails.
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3297
Queensland

Re: T3x 10 moa rail

Post by deye243 » 16 Nov 2026, 6:49 pm

My old bush calculation for this caper was four inch length 0.001" is very close to one MOA
User avatar
deye243
Major
Major
 
Posts: 2835
Victoria

Re: T3x 10 moa rail

Post by Wapiti » 16 Nov 2026, 7:07 pm

Rich's idea is a sound one, if you have the gear down the shed. Or say, you were making a one off where who cares what it costs.
I've got a couple of scope mounts to mill from some solid 4130 over the next few weeks, but blimey, it's only because I have some down time. The hourly rate to charge for that would see me on the net ordering one.
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3297
Queensland

Re: T3x 10 moa rail

Post by scoot » 16 Nov 2026, 7:59 pm

Machining one is possible but like mentioned would be a bit time consuming and detailed job. Keeping recoil pins would add more complexity. It'd be a lot cheaper and easier to setup the adjustable inserts on the burris rings. I hoped someone would make a commercially available one in this ever expanding world of must have accessories.
User avatar
scoot
Corporal
Corporal
 
Posts: 262
South Australia

Re: T3x 10 moa rail

Post by bigrich » 17 Nov 2026, 3:59 am

scoot wrote:Machining one is possible but like mentioned would be a bit time consuming and detailed job. Keeping recoil pins would add more complexity. It'd be a lot cheaper and easier to setup the adjustable inserts on the burris rings. I hoped someone would make a commercially available one in this ever expanding world of must have accessories.


going by your original post that you can either get 0 moa or 20 moa rails with nothing available off the shelf with the moa you want, means getting one custom made to suit is probably the only option IMHO . the burris rings i'm not sure are made anymore , besides , i personally like the idea of a solidly mounted rail with a ring mounted on it over a scope ring with offset nylon bushes . just my personal preference :unknown: . i looked for burris rings a while ago and couldn't find any for sale . getting a smith to help you with this little job could be a challenge . a good smith would have no issue with allowing for recoil pins . my smith i use buys pic rails in long lengths and mills them to suit each job . contact smiths who specialize in building f class rifles as they have probably dealt with this before and have the jigs for milling scope rails, or maybe have one ready to go . one guy in brissy i've heard of has a business called trentech , there's zeirsch in south oz . what's the cost of a phone call ?
hope this helps :thumbsup:
bigrich
General
General
 
Posts: 6756
Queensland

Re: T3x 10 moa rail

Post by Jorlcrin » 17 Nov 2026, 6:08 am

scoot wrote:Machining one is possible but like mentioned would be a bit time consuming and detailed job. Keeping recoil pins would add more complexity. It'd be a lot cheaper and easier to setup the adjustable inserts on the burris rings. I hoped someone would make a commercially available one in this ever expanding world of must have accessories.


Maybe send a query to Ignition Custom Engineering?
https://iceng.com.au/

South Australia based(Pooraka), and they manufacture the 'Manael' brand of accessories, including rails of all sorts.
I note they already machine up rails for Tikka T3's with the recoil pin/lug, with a number of MOA angles to them.

Suspect that if anyone can machine you up a 10MOA rail, they might be the guys for the job.

Just a thought.
Jorlcrin
Corporal
Corporal
 
Posts: 299
Queensland

Re: T3x 10 moa rail

Post by Wapiti » 17 Nov 2026, 7:47 am

Hey Scoot
Just a question mate, do you really need a 10 MOA rail?
If you are after a bit of elevation, just a bit, a 20 will do the job, any scope you have (unless the bore centreline is on the bolt centreline, which hey, it is made by Sako) will comfortably zero at 100, 150, 200 depending on your own personal zero.
Benefits of this are
You'll be able to get a proper steel one
It will be a commonly available item
And if you ever want to stretch your scopes ability a bit further, you can.

Yeah a hunter chasing a rail for more elevation is just a desire not a need whatsoever, but it'll solve your problem immediately.
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3297
Queensland

Re: T3x 10 moa rail

Post by straightshooter » 17 Nov 2026, 8:30 am

I was just about to suggest Ignition Custom Engineering also, ask for Nick.
I recently arranged for a rail for an oddly drilled oversized receiver Schultz & Larsen with them.
You will have to learn patience.
The bigger question is why 10 or 15 MOA?
The industry has settled on 20 MOA for a reason. That being, for the bulk of long range target cartridges 20 MOA positions the elevation towards the middle of of the adjustable range at 900 to 1000 yards thus placing the least restriction on the amount of windage adjustment. These are the ranges where it is most needed.
At ranges such as 500 to 600 yards most scopes will cope without and added taper in the rail.
"Anything is possible if you don't know what you are talking about."
"There is no expedient to which a man will not resort to avoid the real labor of thinking." Sir Joshua Reynolds
straightshooter
Warrant Officer C1
Warrant Officer C1
 
Posts: 1479
New South Wales

Re: T3x 10 moa rail

Post by scoot » 17 Nov 2026, 8:56 am

So the scope is am using only has 40moa of elevation adjustment. I'm fitting it onto a 6mm which will be used for hunting but my local range stretches to 900yards. I was hoping to give it a run there also. It's possible I will get a 100-150 yard zero and still be able to dial out to 900 yards. The electronic targets are run with an extra 2 moa of offset to conserve the aim point. My rough calculations mean the scope will be getting stretched to its outer edges of adjustment which I'm not a fan of. I've just been contemplating the easiest way to get it setup in a permanent way without having to swap scopes or rails etc for range or hunting. I know it's not ideal trying to do 2 different tasks with 1 setup but hey. Once the rifle comes I might just have to see how it plays out.
User avatar
scoot
Corporal
Corporal
 
Posts: 262
South Australia

Re: T3x 10 moa rail

Post by Wapiti » 17 Nov 2026, 9:16 am

Mate, as myself and straightshooter have said, from what you want to do, the best bet for you is the 20 MOA rail.
It will work for you.
And the only restriction you will have is your scope - if you ever upgrade, that set-up will be even more flexible I reckon anyway.
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3297
Queensland

Re: T3x 10 moa rail

Post by straightshooter » 17 Nov 2026, 9:22 am

What you propose makes sense, especially with what sounds like it might be an older 1" tube scope.
What is the scope?
The custom made rail is likely to cost about $300 compared to an off the shelf rail that will probably cost less than $100.
"Anything is possible if you don't know what you are talking about."
"There is no expedient to which a man will not resort to avoid the real labor of thinking." Sir Joshua Reynolds
straightshooter
Warrant Officer C1
Warrant Officer C1
 
Posts: 1479
New South Wales

Re: T3x 10 moa rail

Post by scoot » 17 Nov 2026, 9:38 am

I got a really good deal on a steiner predator 8 scope. 3-24×50. Only got it yesterday bt it seems pretty decent. 30mm tube. I wanted something with low base mag but up to 25 power to be eligible for sporter hunter class. Not a great deal of options around with that criteria. Especially for what I paid.
User avatar
scoot
Corporal
Corporal
 
Posts: 262
South Australia


Back to top
 
Return to Scopes, sights and optics