T3x 10 moa rail

Rifle scopes, iron sights and optics. Spotting scopes and target acquisition devices.

T3x 10 moa rail

Post by scoot » 16 Nov 2026, 12:35 pm

Anyone know where I can find a 10 or 15 moa picatinny rail for a tikka t3x. Everything i can find is 0 or 20 but for what I'm doing a 10 would be more betterer.
I have got some burris zee rings with the offset inserts but I find them a bit tedious to set up initially.
User avatar
scoot
Corporal
Corporal
 
Posts: 266
South Australia

Re: T3x 10 moa rail

Post by bigrich » 16 Nov 2026, 3:56 pm

scoot wrote:Anyone know where I can find a 10 or 15 moa picatinny rail for a tikka t3x. Everything i can find is 0 or 20 but for what I'm doing a 10 would be more betterer.
I have got some burris zee rings with the offset inserts but I find them a bit tedious to set up initially.


maybe find a cluey gun smith or machinist who can machine down a 20 moa rail to what you want . tikka's have a flat topped receiver so it shouldn't be too hard i think . cheers :thumbsup:
bigrich
General
General
 
Posts: 6756
Queensland

Re: T3x 10 moa rail

Post by Wapiti » 16 Nov 2026, 5:43 pm

Yes, do it in a mill.
Grabbing it, setting it up and getting the amount right would take out the calculator mate and get that right. That would cost the price of 4-6 10 MOA factory rails.
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3306
Queensland

Re: T3x 10 moa rail

Post by deye243 » 16 Nov 2026, 6:49 pm

My old bush calculation for this caper was four inch length 0.001" is very close to one MOA
User avatar
deye243
Major
Major
 
Posts: 2836
Victoria

Re: T3x 10 moa rail

Post by Wapiti » 16 Nov 2026, 7:07 pm

Rich's idea is a sound one, if you have the gear down the shed. Or say, you were making a one off where who cares what it costs.
I've got a couple of scope mounts to mill from some solid 4130 over the next few weeks, but blimey, it's only because I have some down time. The hourly rate to charge for that would see me on the net ordering one.
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3306
Queensland

Re: T3x 10 moa rail

Post by scoot » 16 Nov 2026, 7:59 pm

Machining one is possible but like mentioned would be a bit time consuming and detailed job. Keeping recoil pins would add more complexity. It'd be a lot cheaper and easier to setup the adjustable inserts on the burris rings. I hoped someone would make a commercially available one in this ever expanding world of must have accessories.
User avatar
scoot
Corporal
Corporal
 
Posts: 266
South Australia

Re: T3x 10 moa rail

Post by bigrich » 17 Nov 2026, 3:59 am

scoot wrote:Machining one is possible but like mentioned would be a bit time consuming and detailed job. Keeping recoil pins would add more complexity. It'd be a lot cheaper and easier to setup the adjustable inserts on the burris rings. I hoped someone would make a commercially available one in this ever expanding world of must have accessories.


going by your original post that you can either get 0 moa or 20 moa rails with nothing available off the shelf with the moa you want, means getting one custom made to suit is probably the only option IMHO . the burris rings i'm not sure are made anymore , besides , i personally like the idea of a solidly mounted rail with a ring mounted on it over a scope ring with offset nylon bushes . just my personal preference :unknown: . i looked for burris rings a while ago and couldn't find any for sale . getting a smith to help you with this little job could be a challenge . a good smith would have no issue with allowing for recoil pins . my smith i use buys pic rails in long lengths and mills them to suit each job . contact smiths who specialize in building f class rifles as they have probably dealt with this before and have the jigs for milling scope rails, or maybe have one ready to go . one guy in brissy i've heard of has a business called trentech , there's zeirsch in south oz . what's the cost of a phone call ?
hope this helps :thumbsup:
bigrich
General
General
 
Posts: 6756
Queensland

Re: T3x 10 moa rail

Post by Jorlcrin » 17 Nov 2026, 6:08 am

scoot wrote:Machining one is possible but like mentioned would be a bit time consuming and detailed job. Keeping recoil pins would add more complexity. It'd be a lot cheaper and easier to setup the adjustable inserts on the burris rings. I hoped someone would make a commercially available one in this ever expanding world of must have accessories.


Maybe send a query to Ignition Custom Engineering?
https://iceng.com.au/

South Australia based(Pooraka), and they manufacture the 'Manael' brand of accessories, including rails of all sorts.
I note they already machine up rails for Tikka T3's with the recoil pin/lug, with a number of MOA angles to them.

Suspect that if anyone can machine you up a 10MOA rail, they might be the guys for the job.

Just a thought.
Jorlcrin
Corporal
Corporal
 
Posts: 299
Queensland

Re: T3x 10 moa rail

Post by Wapiti » 17 Nov 2026, 7:47 am

Hey Scoot
Just a question mate, do you really need a 10 MOA rail?
If you are after a bit of elevation, just a bit, a 20 will do the job, any scope you have (unless the bore centreline is on the bolt centreline, which hey, it is made by Sako) will comfortably zero at 100, 150, 200 depending on your own personal zero.
Benefits of this are
You'll be able to get a proper steel one
It will be a commonly available item
And if you ever want to stretch your scopes ability a bit further, you can.

Yeah a hunter chasing a rail for more elevation is just a desire not a need whatsoever, but it'll solve your problem immediately.
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3306
Queensland

Re: T3x 10 moa rail

Post by straightshooter » 17 Nov 2026, 8:30 am

I was just about to suggest Ignition Custom Engineering also, ask for Nick.
I recently arranged for a rail for an oddly drilled oversized receiver Schultz & Larsen with them.
You will have to learn patience.
The bigger question is why 10 or 15 MOA?
The industry has settled on 20 MOA for a reason. That being, for the bulk of long range target cartridges 20 MOA positions the elevation towards the middle of of the adjustable range at 900 to 1000 yards thus placing the least restriction on the amount of windage adjustment. These are the ranges where it is most needed.
At ranges such as 500 to 600 yards most scopes will cope without and added taper in the rail.
"Anything is possible if you don't know what you are talking about."
"There is no expedient to which a man will not resort to avoid the real labor of thinking." Sir Joshua Reynolds
straightshooter
Warrant Officer C1
Warrant Officer C1
 
Posts: 1480
New South Wales

Re: T3x 10 moa rail

Post by scoot » 17 Nov 2026, 8:56 am

So the scope is am using only has 40moa of elevation adjustment. I'm fitting it onto a 6mm which will be used for hunting but my local range stretches to 900yards. I was hoping to give it a run there also. It's possible I will get a 100-150 yard zero and still be able to dial out to 900 yards. The electronic targets are run with an extra 2 moa of offset to conserve the aim point. My rough calculations mean the scope will be getting stretched to its outer edges of adjustment which I'm not a fan of. I've just been contemplating the easiest way to get it setup in a permanent way without having to swap scopes or rails etc for range or hunting. I know it's not ideal trying to do 2 different tasks with 1 setup but hey. Once the rifle comes I might just have to see how it plays out.
User avatar
scoot
Corporal
Corporal
 
Posts: 266
South Australia

Re: T3x 10 moa rail

Post by Wapiti » 17 Nov 2026, 9:16 am

Mate, as myself and straightshooter have said, from what you want to do, the best bet for you is the 20 MOA rail.
It will work for you.
And the only restriction you will have is your scope - if you ever upgrade, that set-up will be even more flexible I reckon anyway.
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3306
Queensland

Re: T3x 10 moa rail

Post by straightshooter » 17 Nov 2026, 9:22 am

What you propose makes sense, especially with what sounds like it might be an older 1" tube scope.
What is the scope?
The custom made rail is likely to cost about $300 compared to an off the shelf rail that will probably cost less than $100.
"Anything is possible if you don't know what you are talking about."
"There is no expedient to which a man will not resort to avoid the real labor of thinking." Sir Joshua Reynolds
straightshooter
Warrant Officer C1
Warrant Officer C1
 
Posts: 1480
New South Wales

Re: T3x 10 moa rail

Post by scoot » 17 Nov 2026, 9:38 am

I got a really good deal on a steiner predator 8 scope. 3-24×50. Only got it yesterday bt it seems pretty decent. 30mm tube. I wanted something with low base mag but up to 25 power to be eligible for sporter hunter class. Not a great deal of options around with that criteria. Especially for what I paid.
User avatar
scoot
Corporal
Corporal
 
Posts: 266
South Australia

Re: T3x 10 moa rail

Post by straightshooter » 17 Nov 2026, 11:04 am

scoot wrote:I got a really good deal on a steiner predator 8 scope. 3-24×50. Only got it yesterday bt it seems pretty decent. 30mm tube. I wanted something with low base mag but up to 25 power to be eligible for sporter hunter class. Not a great deal of options around with that criteria. Especially for what I paid.

I had a look at the specs and they don't make it clear clear whether elevation is 40 moa in total or + - 40 moa.
If it is + - 40 moa then just use a 20 moa rail and you wont have any issues. If in fact it is + - 20 moa then you will have to do some calculating to to decide on 10 moa or 15 moa because depending cartridge and projectile you could easily need 30 moa or more to go from your hunting zero to a 900 yard zero.
You can easily confirm the true scope elevation range by clamping the scope to something secure and looking at say a brick wall at a known distance and counting the number of brick courses the elevation traverses. A standard Australian brick course is 86 mm. You might have to disable the zero stop if it has one.

Having looked at the Steiner specs I am now getting buyer's regret because I recently bought a Zeiss Conquest V4 6-24 for much the same purpose as you but probably paid more than you paid for the Steiner.
"Anything is possible if you don't know what you are talking about."
"There is no expedient to which a man will not resort to avoid the real labor of thinking." Sir Joshua Reynolds
straightshooter
Warrant Officer C1
Warrant Officer C1
 
Posts: 1480
New South Wales

Re: T3x 10 moa rail

Post by scoot » 17 Nov 2026, 1:04 pm

The rifle is coming with a 20moa rail. I might have to see if I can get a 100 yard zero with normal rings and see how much elevation I have left. If it's too far on the extremes of adjustment I might just have to spend some time with the burris rings to get the right offset inserts and ring spacing to achieve the best outcome.
User avatar
scoot
Corporal
Corporal
 
Posts: 266
South Australia

Re: T3x 10 moa rail

Post by Wapiti » 17 Nov 2026, 3:34 pm

It'd HAVE to be 40moa up and 40 down each side of centre = 80MOA total from the Steiner, surely?
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3306
Queensland

Re: T3x 10 moa rail

Post by Wapiti » 17 Nov 2026, 3:37 pm

Anyway, good luck with your journey.
Nothing advances your future equipment needs more than deficiencies.
Numbers aint numbers, Sol? Untrue.
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3306
Queensland

Re: T3x 10 moa rail

Post by scoot » 17 Nov 2026, 7:00 pm

Just had a look. It seems with the zero stop in play there is only one complete revolution of elevation adjustment available. 15moa. Looks like that will need to be disengaged or removed to allow multiple turns of elevation.
Without pulling it apart to physically test travel without zero stop I can't confirm yet but 40moa total seems plausible. My guess is that being an 8x zoom ratio, comprimises were made to optimise the image through a complex lens system without getting too costly, technical or unreliable. It is after all marketed as a "hunting' optic where dialling is generally not a concern. Especially more than the 15moa from zero stop. At 1/2 the price of the nightforce nx8 its a compromise I'm happy to accept if all else pans out ok.
Thanks everyone for some insightful input. Once I get hands on it'll be interesting to see how it all stacks up. Im sure there will be some "quirks" but that can be said about anything..
User avatar
scoot
Corporal
Corporal
 
Posts: 266
South Australia

Re: T3x 10 moa rail

Post by scoot » 17 Nov 2026, 7:24 pm

Wow... Google sucks balls. Some info says 40moa total, some say 40moa either side of optical centre ie 80moa. Some say zero stop can be removed completely, some say just loosen it off and leave in. Then there's the can't get around zero stop. I think I need to stop thinking and start doing. :wtf:
User avatar
scoot
Corporal
Corporal
 
Posts: 266
South Australia

Re: T3x 10 moa rail

Post by Wapiti » 18 Nov 2026, 6:39 am

scoot wrote:Just had a look. It seems with the zero stop in play there is only one complete revolution of elevation adjustment available. 15moa. Looks like that will need to be disengaged or removed to allow multiple turns of elevation.
Without pulling it apart to physically test travel without zero stop I can't confirm yet but 40moa total seems plausible. My guess is that being an 8x zoom ratio, comprimises were made to optimise the image through a complex lens system without getting too costly, technical or unreliable. It is after all marketed as a "hunting' optic where dialling is generally not a concern. Especially more than the 15moa from zero stop. At 1/2 the price of the nightforce nx8 its a compromise I'm happy to accept if all else pans out ok.
Thanks everyone for some insightful input. Once I get hands on it'll be interesting to see how it all stacks up. Im sure there will be some "quirks" but that can be said about anything..


Mate, that's interesting to me.
Especially with the pioneers of that kind of scope, not having any of that trouble, or at least being so intuitive.

I just don't get where gear is going - My four MK4's and 5, and two NF NXS's just go up, up, up all the way from the zero stop without taking your eye off the stock. Or changing how the optic comes straight out of the box.
NXS has 100MOA, I do believe MK4 is less than that but Once I found it past 1000 with a 0 moa rail, which was the only one I could get at the time in stock for the 338L TRG, so I swapped it for another steel 20 moa job and that fixed it. But you will always find a limit, no matter what you do.

To get the most from the scope, you use the most ski-ramp rail available, and being right down in the lower 1/8th of the elevation range has no issue with clarity, image or zero-hold when getting the 0 moa @100 zero I use.
It's so simple. Why would a scope maker make it so unintuitive other than just setting a stop and turning?

Gotta be something else there mate, surely?
I know the scopes I mention cost two Steiners, but why not just reverse-engineer simplicity?
Imagine a military or hardcore user putting up with that.

IF the moa range is that limited - after a set point, perhaps you have a reticle with multiple easily switched-to zero points down lower you can use as a reset when going further out when you run out of elevation.
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3306
Queensland

Re: T3x 10 moa rail

Post by scoot » 18 Nov 2026, 7:53 am

So it got the better of me and i pulled the elevation turret apart last night. With the "turret" off i can confirm it has about 45moa of adjustment either side of optical zero. 90 ish total travel.
Zero stop is another issue. It's a very basic design where a pin exists on the scope body. This pin rides in a channel machined into the turret "cap". Once the zero stop is set, pin hard up against the edge of channel machined in cap you only get just under 1 turn of elevation before the pin contacts the opposite side of the "stop"
IMG_20261118_080919.jpg
IMG_20261118_080919.jpg (225.16 KiB) Viewed 8 times

The only way ican see to get multiple turns of elevation is to file off the pin (not doing that) or machine out the hard edge "stop" on the turret cap so the pin has nowhere to stop against. This will solve only one turn of elevation but does leave you without a zero stop function.at all. I sent beretta an email about buying a spare turret to butcher. Would have been nice to have both zero stop and multi turn elevation but whatever.....
User avatar
scoot
Corporal
Corporal
 
Posts: 266
South Australia


Back to top
 
Return to Scopes, sights and optics