T3x 10 moa rail

Rifle scopes, iron sights and optics. Spotting scopes and target acquisition devices.

T3x 10 moa rail

Post by scoot » 16 Nov 2026, 12:35 pm

Anyone know where I can find a 10 or 15 moa picatinny rail for a tikka t3x. Everything i can find is 0 or 20 but for what I'm doing a 10 would be more betterer.
I have got some burris zee rings with the offset inserts but I find them a bit tedious to set up initially.
User avatar
scoot
Corporal
Corporal
 
Posts: 268
South Australia

Re: T3x 10 moa rail

Post by bigrich » 16 Nov 2026, 3:56 pm

scoot wrote:Anyone know where I can find a 10 or 15 moa picatinny rail for a tikka t3x. Everything i can find is 0 or 20 but for what I'm doing a 10 would be more betterer.
I have got some burris zee rings with the offset inserts but I find them a bit tedious to set up initially.


maybe find a cluey gun smith or machinist who can machine down a 20 moa rail to what you want . tikka's have a flat topped receiver so it shouldn't be too hard i think . cheers :thumbsup:
bigrich
General
General
 
Posts: 6759
Queensland

Re: T3x 10 moa rail

Post by Wapiti » 16 Nov 2026, 5:43 pm

Yes, do it in a mill.
Grabbing it, setting it up and getting the amount right would take out the calculator mate and get that right. That would cost the price of 4-6 10 MOA factory rails.
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3313
Queensland

Re: T3x 10 moa rail

Post by deye243 » 16 Nov 2026, 6:49 pm

My old bush calculation for this caper was four inch length 0.001" is very close to one MOA
User avatar
deye243
Major
Major
 
Posts: 2837
Victoria

Re: T3x 10 moa rail

Post by Wapiti » 16 Nov 2026, 7:07 pm

Rich's idea is a sound one, if you have the gear down the shed. Or say, you were making a one off where who cares what it costs.
I've got a couple of scope mounts to mill from some solid 4130 over the next few weeks, but blimey, it's only because I have some down time. The hourly rate to charge for that would see me on the net ordering one.
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3313
Queensland

Re: T3x 10 moa rail

Post by scoot » 16 Nov 2026, 7:59 pm

Machining one is possible but like mentioned would be a bit time consuming and detailed job. Keeping recoil pins would add more complexity. It'd be a lot cheaper and easier to setup the adjustable inserts on the burris rings. I hoped someone would make a commercially available one in this ever expanding world of must have accessories.
User avatar
scoot
Corporal
Corporal
 
Posts: 268
South Australia

Re: T3x 10 moa rail

Post by bigrich » 17 Nov 2026, 3:59 am

scoot wrote:Machining one is possible but like mentioned would be a bit time consuming and detailed job. Keeping recoil pins would add more complexity. It'd be a lot cheaper and easier to setup the adjustable inserts on the burris rings. I hoped someone would make a commercially available one in this ever expanding world of must have accessories.


going by your original post that you can either get 0 moa or 20 moa rails with nothing available off the shelf with the moa you want, means getting one custom made to suit is probably the only option IMHO . the burris rings i'm not sure are made anymore , besides , i personally like the idea of a solidly mounted rail with a ring mounted on it over a scope ring with offset nylon bushes . just my personal preference :unknown: . i looked for burris rings a while ago and couldn't find any for sale . getting a smith to help you with this little job could be a challenge . a good smith would have no issue with allowing for recoil pins . my smith i use buys pic rails in long lengths and mills them to suit each job . contact smiths who specialize in building f class rifles as they have probably dealt with this before and have the jigs for milling scope rails, or maybe have one ready to go . one guy in brissy i've heard of has a business called trentech , there's zeirsch in south oz . what's the cost of a phone call ?
hope this helps :thumbsup:
bigrich
General
General
 
Posts: 6759
Queensland

Re: T3x 10 moa rail

Post by Jorlcrin » 17 Nov 2026, 6:08 am

scoot wrote:Machining one is possible but like mentioned would be a bit time consuming and detailed job. Keeping recoil pins would add more complexity. It'd be a lot cheaper and easier to setup the adjustable inserts on the burris rings. I hoped someone would make a commercially available one in this ever expanding world of must have accessories.


Maybe send a query to Ignition Custom Engineering?
https://iceng.com.au/

South Australia based(Pooraka), and they manufacture the 'Manael' brand of accessories, including rails of all sorts.
I note they already machine up rails for Tikka T3's with the recoil pin/lug, with a number of MOA angles to them.

Suspect that if anyone can machine you up a 10MOA rail, they might be the guys for the job.

Just a thought.
Jorlcrin
Corporal
Corporal
 
Posts: 301
Queensland

Re: T3x 10 moa rail

Post by Wapiti » 17 Nov 2026, 7:47 am

Hey Scoot
Just a question mate, do you really need a 10 MOA rail?
If you are after a bit of elevation, just a bit, a 20 will do the job, any scope you have (unless the bore centreline is on the bolt centreline, which hey, it is made by Sako) will comfortably zero at 100, 150, 200 depending on your own personal zero.
Benefits of this are
You'll be able to get a proper steel one
It will be a commonly available item
And if you ever want to stretch your scopes ability a bit further, you can.

Yeah a hunter chasing a rail for more elevation is just a desire not a need whatsoever, but it'll solve your problem immediately.
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3313
Queensland

Re: T3x 10 moa rail

Post by straightshooter » 17 Nov 2026, 8:30 am

I was just about to suggest Ignition Custom Engineering also, ask for Nick.
I recently arranged for a rail for an oddly drilled oversized receiver Schultz & Larsen with them.
You will have to learn patience.
The bigger question is why 10 or 15 MOA?
The industry has settled on 20 MOA for a reason. That being, for the bulk of long range target cartridges 20 MOA positions the elevation towards the middle of of the adjustable range at 900 to 1000 yards thus placing the least restriction on the amount of windage adjustment. These are the ranges where it is most needed.
At ranges such as 500 to 600 yards most scopes will cope without and added taper in the rail.
"Anything is possible if you don't know what you are talking about."
"There is no expedient to which a man will not resort to avoid the real labor of thinking." Sir Joshua Reynolds
straightshooter
Warrant Officer C1
Warrant Officer C1
 
Posts: 1481
New South Wales

Re: T3x 10 moa rail

Post by scoot » 17 Nov 2026, 8:56 am

So the scope is am using only has 40moa of elevation adjustment. I'm fitting it onto a 6mm which will be used for hunting but my local range stretches to 900yards. I was hoping to give it a run there also. It's possible I will get a 100-150 yard zero and still be able to dial out to 900 yards. The electronic targets are run with an extra 2 moa of offset to conserve the aim point. My rough calculations mean the scope will be getting stretched to its outer edges of adjustment which I'm not a fan of. I've just been contemplating the easiest way to get it setup in a permanent way without having to swap scopes or rails etc for range or hunting. I know it's not ideal trying to do 2 different tasks with 1 setup but hey. Once the rifle comes I might just have to see how it plays out.
User avatar
scoot
Corporal
Corporal
 
Posts: 268
South Australia

Re: T3x 10 moa rail

Post by Wapiti » 17 Nov 2026, 9:16 am

Mate, as myself and straightshooter have said, from what you want to do, the best bet for you is the 20 MOA rail.
It will work for you.
And the only restriction you will have is your scope - if you ever upgrade, that set-up will be even more flexible I reckon anyway.
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3313
Queensland

Re: T3x 10 moa rail

Post by straightshooter » 17 Nov 2026, 9:22 am

What you propose makes sense, especially with what sounds like it might be an older 1" tube scope.
What is the scope?
The custom made rail is likely to cost about $300 compared to an off the shelf rail that will probably cost less than $100.
"Anything is possible if you don't know what you are talking about."
"There is no expedient to which a man will not resort to avoid the real labor of thinking." Sir Joshua Reynolds
straightshooter
Warrant Officer C1
Warrant Officer C1
 
Posts: 1481
New South Wales

Re: T3x 10 moa rail

Post by scoot » 17 Nov 2026, 9:38 am

I got a really good deal on a steiner predator 8 scope. 3-24×50. Only got it yesterday bt it seems pretty decent. 30mm tube. I wanted something with low base mag but up to 25 power to be eligible for sporter hunter class. Not a great deal of options around with that criteria. Especially for what I paid.
User avatar
scoot
Corporal
Corporal
 
Posts: 268
South Australia

Re: T3x 10 moa rail

Post by straightshooter » 17 Nov 2026, 11:04 am

scoot wrote:I got a really good deal on a steiner predator 8 scope. 3-24×50. Only got it yesterday bt it seems pretty decent. 30mm tube. I wanted something with low base mag but up to 25 power to be eligible for sporter hunter class. Not a great deal of options around with that criteria. Especially for what I paid.

I had a look at the specs and they don't make it clear clear whether elevation is 40 moa in total or + - 40 moa.
If it is + - 40 moa then just use a 20 moa rail and you wont have any issues. If in fact it is + - 20 moa then you will have to do some calculating to to decide on 10 moa or 15 moa because depending cartridge and projectile you could easily need 30 moa or more to go from your hunting zero to a 900 yard zero.
You can easily confirm the true scope elevation range by clamping the scope to something secure and looking at say a brick wall at a known distance and counting the number of brick courses the elevation traverses. A standard Australian brick course is 86 mm. You might have to disable the zero stop if it has one.

Having looked at the Steiner specs I am now getting buyer's regret because I recently bought a Zeiss Conquest V4 6-24 for much the same purpose as you but probably paid more than you paid for the Steiner.
"Anything is possible if you don't know what you are talking about."
"There is no expedient to which a man will not resort to avoid the real labor of thinking." Sir Joshua Reynolds
straightshooter
Warrant Officer C1
Warrant Officer C1
 
Posts: 1481
New South Wales

Re: T3x 10 moa rail

Post by scoot » 17 Nov 2026, 1:04 pm

The rifle is coming with a 20moa rail. I might have to see if I can get a 100 yard zero with normal rings and see how much elevation I have left. If it's too far on the extremes of adjustment I might just have to spend some time with the burris rings to get the right offset inserts and ring spacing to achieve the best outcome.
User avatar
scoot
Corporal
Corporal
 
Posts: 268
South Australia

Re: T3x 10 moa rail

Post by Wapiti » 17 Nov 2026, 3:34 pm

It'd HAVE to be 40moa up and 40 down each side of centre = 80MOA total from the Steiner, surely?
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3313
Queensland

Re: T3x 10 moa rail

Post by Wapiti » 17 Nov 2026, 3:37 pm

Anyway, good luck with your journey.
Nothing advances your future equipment needs more than deficiencies.
Numbers aint numbers, Sol? Untrue.
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3313
Queensland

Re: T3x 10 moa rail

Post by scoot » 17 Nov 2026, 7:00 pm

Just had a look. It seems with the zero stop in play there is only one complete revolution of elevation adjustment available. 15moa. Looks like that will need to be disengaged or removed to allow multiple turns of elevation.
Without pulling it apart to physically test travel without zero stop I can't confirm yet but 40moa total seems plausible. My guess is that being an 8x zoom ratio, comprimises were made to optimise the image through a complex lens system without getting too costly, technical or unreliable. It is after all marketed as a "hunting' optic where dialling is generally not a concern. Especially more than the 15moa from zero stop. At 1/2 the price of the nightforce nx8 its a compromise I'm happy to accept if all else pans out ok.
Thanks everyone for some insightful input. Once I get hands on it'll be interesting to see how it all stacks up. Im sure there will be some "quirks" but that can be said about anything..
User avatar
scoot
Corporal
Corporal
 
Posts: 268
South Australia

Re: T3x 10 moa rail

Post by scoot » 17 Nov 2026, 7:24 pm

Wow... Google sucks balls. Some info says 40moa total, some say 40moa either side of optical centre ie 80moa. Some say zero stop can be removed completely, some say just loosen it off and leave in. Then there's the can't get around zero stop. I think I need to stop thinking and start doing. :wtf:
User avatar
scoot
Corporal
Corporal
 
Posts: 268
South Australia

Re: T3x 10 moa rail

Post by Wapiti » 18 Nov 2026, 6:39 am

scoot wrote:Just had a look. It seems with the zero stop in play there is only one complete revolution of elevation adjustment available. 15moa. Looks like that will need to be disengaged or removed to allow multiple turns of elevation.
Without pulling it apart to physically test travel without zero stop I can't confirm yet but 40moa total seems plausible. My guess is that being an 8x zoom ratio, comprimises were made to optimise the image through a complex lens system without getting too costly, technical or unreliable. It is after all marketed as a "hunting' optic where dialling is generally not a concern. Especially more than the 15moa from zero stop. At 1/2 the price of the nightforce nx8 its a compromise I'm happy to accept if all else pans out ok.
Thanks everyone for some insightful input. Once I get hands on it'll be interesting to see how it all stacks up. Im sure there will be some "quirks" but that can be said about anything..


Mate, that's interesting to me.
Especially with the pioneers of that kind of scope, not having any of that trouble, or at least being so intuitive.

I just don't get where gear is going - My four MK4's and 5, and two NF NXS's just go up, up, up all the way from the zero stop without taking your eye off the stock. Or changing how the optic comes straight out of the box.
NXS has 100MOA, I do believe MK4 is less than that but Once I found it past 1000 with a 0 moa rail, which was the only one I could get at the time in stock for the 338L TRG, so I swapped it for another steel 20 moa job and that fixed it. But you will always find a limit, no matter what you do.

To get the most from the scope, you use the most ski-ramp rail available, and being right down in the lower 1/8th of the elevation range has no issue with clarity, image or zero-hold when getting the 0 moa @100 zero I use.
It's so simple. Why would a scope maker make it so unintuitive other than just setting a stop and turning?

Gotta be something else there mate, surely?
I know the scopes I mention cost two Steiners, but why not just reverse-engineer simplicity?
Imagine a military or hardcore user putting up with that.

IF the moa range is that limited - after a set point, perhaps you have a reticle with multiple easily switched-to zero points down lower you can use as a reset when going further out when you run out of elevation.
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3313
Queensland

Re: T3x 10 moa rail

Post by scoot » 18 Nov 2026, 7:53 am

So it got the better of me and i pulled the elevation turret apart last night. With the "turret" off i can confirm it has about 45moa of adjustment either side of optical zero. 90 ish total travel.
Zero stop is another issue. It's a very basic design where a pin exists on the scope body. This pin rides in a channel machined into the turret "cap". Once the zero stop is set, pin hard up against the edge of channel machined in cap you only get just under 1 turn of elevation before the pin contacts the opposite side of the "stop"
IMG_20261118_080919.jpg
IMG_20261118_080919.jpg (225.16 KiB) Viewed 97 times

The only way ican see to get multiple turns of elevation is to file off the pin (not doing that) or machine out the hard edge "stop" on the turret cap so the pin has nowhere to stop against. This will solve only one turn of elevation but does leave you without a zero stop function.at all. I sent beretta an email about buying a spare turret to butcher. Would have been nice to have both zero stop and multi turn elevation but whatever.....
User avatar
scoot
Corporal
Corporal
 
Posts: 268
South Australia

Re: T3x 10 moa rail

Post by straightshooter » 18 Nov 2026, 9:39 am

Scoot
I helped a friend with the same problem a few months ago but his scope was a Nikko although the zero stop mechanism appears to be the same.
The simplest thing is to pull out the pin and sticky tape it to a piece of paper saying what it is.
Although pressed in, the pin will come out easily enough with a pin vice or pliers being careful not to bend or mar the pin.
So now comes another problem depending on whether the turret can be seen to move up and down.
If the turret moves up and down then once you have established your zero at say 300 yards you can scribe a fine line on the inner part that is just visible below the skirt of the turret when the turret zero aligns with the zero reference.
If the turret doesn't move up and down then after establishing your reference zero you will have to count how many moa you went up for that range on that day and religiously on completion of your shoot on that day count the same number of moa back to zero. It would be wise to keep a diary of settings also noting a change in projectile and load.
"Anything is possible if you don't know what you are talking about."
"There is no expedient to which a man will not resort to avoid the real labor of thinking." Sir Joshua Reynolds
straightshooter
Warrant Officer C1
Warrant Officer C1
 
Posts: 1481
New South Wales

Re: T3x 10 moa rail

Post by Wapiti » 18 Nov 2026, 10:13 am

A scope like that would have to have a micrometer-type set of lines and centre-point line etched into it surely?
So, when back to zero mark against the vertical line, you could easily tell if you were under it or over it by a rotation.
Then you wouldn't need to record anything, with the pin removed, if those essential micrometer-type marks are there.
Surely?

You can do that with any old scope without zero-stop too. As long as you have those markings. If you need to scribe lines, to me it's obvious you would have an amateur piece of gear. That's not meant to upset or to denigrate by the way, is what it is.
But if you need to do that, you need to.
Problem for consumers of this gear is, the person on the opposite side of the counter asks what your price range is and fill it. Real advice on the options out there are not a consideration WAY too often.
That isn't meant for Scoot, it's meant for anyone thinking of stepping up, FFS do your homework independent of most counter staff. The old "those staff have been there 20 years and are great" doesn't mean much. The ones I met yesterday were really nice people, but knowing products against one another other than cost, fail bigtime in what I just mentioned.

The only Steiner gear I've had experience with are their higher-end line of binos, and I will not upset anyone rating their optical sharpness compared to other stuff from the same country.
There is a point where cost (if the brand of gear is right and it's just not marketing vomit) actually becomes superb and you see things you never did before, or experienced images so sharp and bright it ruins everything else.
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3313
Queensland

Re: T3x 10 moa rail

Post by scoot » 18 Nov 2026, 11:12 am

I'm picking up what you're putting down. I'll try and describe what's going on since it has no vertical hash marks to indicate the level of rotations. At the centre of it all is the "mechanical" turret with just a flathead slot to adjust clicks up or down when everything else is stripped off. Then another conventional sized cap/turret fits over the top of this entire mechanism and secures to it with 3 grub screws. Hence when you turn the turret the actual mechanism turns also. There are 4 sleeves that then slide over the outside of the turret, one with all the moa graduations and 3 with just reference points for say 200, 300, 400yard zero's. These are held in place with another clear sleeve covering them all and a retainer cap. This all functions like any non tactical hunting style turret where the only reference you have is the moa distances moved from zero. It doesn't give any reference to what rotation that you're on. The theory is you setup you're 100yard zero. Loosen the grub screws on the turret and set it up against the zero stop pin. Secure the grub screws. Align the 0 marks on the sleeves at the relevant positions before tightening down the retainer cap. Due to the zero stop design you only get that one rotation before hitting the reverse edge of the zero stop.
One rotation of 14-15 moa is probably enough to get from 100yards to 5 or 600yards. Plenty for hunting. My only problem is trying to use 1 scope for two different duties. Yes I could have bought a more "tacical" scope better for long range but then there would be just as many compromises when it comes to low end hunting. Ie base mag, reticles, ffp, cost, etc.
This is really only an experiment for me to see what happens. If it works great, if not I'll put it on something else and use my kahles or nightforce or buy something more appropriate. When I've started using it I'll soon find any shortcomings that bug me. For the amount of times it'll be shot past 500yards I can probably just delete the zero stop and remember how many turns I'm on.
User avatar
scoot
Corporal
Corporal
 
Posts: 268
South Australia

Re: T3x 10 moa rail

Post by scoot » 18 Nov 2026, 11:28 am

My other option is to leave the zero stop in and use the bdc reticle to dial a long range zero to one of the lower stadia. This will probably keep it within the one revolution.
User avatar
scoot
Corporal
Corporal
 
Posts: 268
South Australia

Re: T3x 10 moa rail

Post by Wapiti » 18 Nov 2026, 12:39 pm

Geeze man, a bit of fun there. Sounds like you will work it out and eventually it'll be easier.

The craze for FFP scopes is just a pain.
As is the case to provide a point of difference that's just plain marketing.
Years ago I bought some older 2FP Mk4 and NXS's, and I haven't met anybody that can come up with a practical reason for putting them back in the boxes and buying the newer models in FFP. Which I did, despite thinking it was incorrect for the practical use I was putting the gear through.
I gained absolutely nothing, and spent multi $1000s on nothing.
On top of that, dialling these types of scopes down to try and make them hunting scopes at lower power is pointless. The idiotic change to reticle useability and terrible FOV compared to a proper SFP hunting scope is like running a marathon on crutches.
bulls**t it hear people saying - but when you have the two side x side I will pick up the 2FP scope every time. In fact now, ones come off for its replacement.
You can spend a bucket load of dough on stuff that's supposed to be an improvement, and then try to convince everyone else of the same out of pride. Yeah sure you've got the latest "expert" choices, but any hope of flexibility is now gone.
The other thing of course is that no matter the bottom limit of a scopes magnification range, especially with a higher upper, the smaller the FOV, the duller and less crisp the image is, the more parts in the scope and the less the ultimate reliability to the point of pointlessness. Example- the best optics makers won't make a 1-10x until they solve the problems everyone else just accepts and hands to the customer who just accepts the numbers.
Nowadays I use it as a judge whether or not I should listen to someone ever again. Might sound harsh, but as my new t-shirt says...
At the end of the day, both ends of the spectrum, when even at their best in that class, do not overlap.
"The only way to avoid criticism is to do nothing, say nothing, and be nothing."
Aristotle.
Regards G,
AKA "Dr. Doolittle"
A term given to me by a departed forum member, meant to insult... but it's me to a tee.
Wapiti
Lieutenant Colonel
Lieutenant Colonel
 
Posts: 3313
Queensland


Back to top
 
Return to Scopes, sights and optics